News:

Printed Amstrad Addict magazine announced, check it out here!

Main Menu

C4CPC FW update

Started by gerald, 16:41, 09 September 15

Previous topic - Next topic

0 Members and 1 Guest are viewing this topic.

fille1976

updated mine yesterday,checked the cards firmware starting it without sdcard,says 1.05
so everything went fine,played after the update xenon.

gerald

Just released a new version fixing issue mentioned here
See 1st post or C4CPC wiki page

00WReX

Update successful  ;)

QuoteC:\C4CPC_V1.00.07\windows>UpdateCartEmu.bat
Manufacturer Code: 0x58 (88)
"--- Erase ---"
Erasing flash...  Success
Checking memory from 0x0 to 0x6FFF...  Empty.
"--- Flash ---"
Checking memory from 0x0 to 0x4F7F...  Empty.
0%                            100%  Programming 0x4F80 bytes...
[>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>]  Success
0%                            100%  Reading 0x7000 bytes...
[>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>]  Success
Validating...  Success
0x4F80 bytes written into 0x7000 bytes memory (70.98%).
"--- EEProm ---"
0%                            100%  Programming 0x400 bytes...
[>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>]  Success
0%                            100%  Reading 0x400 bytes...
[>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>]  Success
Validating...  Success
0x400 bytes written into 0x400 bytes memory (100.00%).

C:\C4CPC_V1.00.07\windows>

Thanks Gerald.

Cheers,
Shane
The CPC in Australia...
Awa - CPCWiki

rickyordi

#53
Hello Gerald,

I have two questions :

Is it normal that at the time of the firmware execution, that the terminal closes quickly by itself and that I do not see the end ?

I see so far:

Manufacturer Code: 0x58 (88)
"--- Erase ---"
Erasing flash...  Success
Checking memory from 0x0 to 0x6FFF...  Empty.
"--- Flash ---"
Checking memory from 0x0 to 0x4F7F...  Empty.
0%                            100%  Programming 0x4F80 bytes...
[>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>]  Success
0%                            100%  Reading 0x7000 bytes...
[>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>]  Success
Validating...  Success
0x4F80 bytes written into 0x7000 bytes memory (70.98%).
"--- EEProm ---"
0%                            100%  Programming 0x400 bytes...
[>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>]  Success


After checking the firmware by removing the SD card, I see this :
C4CPC :_00_07

Is that normal ?

Best regards,
Eric

gerald


asertus

Hi, just a little update for this thread. Maybe you already know the issue, but I have just found it.


I had "deleted" my c4cpc configuration, but as I was using M4 I did not worry much. I have tried to restore it, installing 1.07, etc.., but I was unable, wrong drivers and device not found in windows 10. Finally, this morning, I found out the drivers for AT32UC3A3 in windows 10. Here the links

Install one of
http://studio.download.atmel.com/7.0.1931/driver-libusb0-installer-x64-7.0.1931.msi or http://studio.download.atmel.com/7.0.1931/driver-libusb0-installer-x86-7.0.1931.msi and one of http://studio.download.atmel.com/7.0.1931/driver-atmel-installer-x64-7.0.1931.msi or http://studio.download.atmel.com/7.0.1931/driver-atmel-installer-x86-7.0.1931.msi


And here the thread.. https://www.avrfreaks.net/forum/atmel-chipset-windows-10-driver-signature


I have installed the x64 versions and it worked fine and my c4cpc is alive again, run UpdateCartEmu.bat from the pack, C4CPC_V1.00.07.zip and everything went fine


Just for anyone who might be interested.



Powered by SMFPacks Menu Editor Mod