avatar_Starglider

How to fix PCW drive "missing address mark"?

Started by Starglider, 03:10, 22 September 15

Previous topic - Next topic

0 Members and 1 Guest are viewing this topic.

Starglider

I thought it would be a good idea to move the discussion away from the "Wanted" board and into a more focussed area to hopefully pick up some PCW experts.

Please take a look at this thread about my EME-232 drive that I have installed as "Drive B" in a PCW 8256: http://www.cpcwiki.eu/forum/classifieds/wanted-amstrad-3-inch-floppy-disk-drive-compatible-with-pcw8256-pcw8512/msg109611/#msg109611

Quote
I ... reversed wires 4 and 6 [to allow the drive to be "B:"] as per the article ... Photo: https://goo.gl/b5k8wl

Good news! Now Drive A boots and Drive B appears to the system!

Bad news! I'm getting an error on any disk inserted into Drive B, even disks that boot fine in Drive A. The disk "groans" back and forth twice then says:

B: track 0, sector 0 missing address mark

It has been suggested that it could be a head alignment, or calibration, or head cleaning issue.

- I have cleaned the heads
- Calibration looks very complex with CAD charts etc. when we're not sure if that's it
- I am buying some blank 3" disks from @pacomix to test writing with

Could there be a simpler fix? Is it an issue with my swapping the wires perhaps? Here's where I'm up to:

Quote
Does anyone know of a 'fudge' to mess around with alignment temporarily? Truth be told I only need access to the DD drive once, to read an old childhood disk. Once I've read it and seen the contents I'll be satisfied  ;D

I want to do that on my own, so any tips for what to either push on or prod or screw or unscrew, that aren't as complex as the instructions at the above referenced site (creating CAD charts etc.) would be greatly appreciated. As would any disk alignment software or other pointers to what could be wrong here.
Starglider aka Perifractic
http://youtube.com/perifractic 

Amstrad PCW8256 with Gotek & HD Drive B

Bryce

If it really is just a once off thing, you could try blindly adjusting the RPMs. Try reading the disk. Then turn the adjust screw about 5% clockwise and try reading again. If it doesn't work turn the screw 10% anti-clockwise and try reading the disk again.

Blind head alignment is more or less impossible, so I wouldn't even try that.

Bryce.

Starglider

Thanks. Could you advise location of screw?

Thanks!

"Recordar es vivir"

Starglider aka Perifractic
http://youtube.com/perifractic 

Amstrad PCW8256 with Gotek & HD Drive B

Bryce

Not sure about the EME-232, either it's directly on the motor or on the PCB. Maybe you can compare yours with the pictures here: Amstrad FDD part - CPCWiki  Or post some pictures of the motor and entire PCB from yours.

Bryce.

Starglider

Starglider aka Perifractic
http://youtube.com/perifractic 

Amstrad PCW8256 with Gotek & HD Drive B

gerald

Quote from: Bryce on 14:11, 22 September 15
Not sure about the EME-232, either it's directly on the motor or on the PCB. Maybe you can compare yours with the pictures here: Amstrad FDD part - CPCWiki  Or post some pictures of the motor and entire PCB from yours.

Bryce.
Looking at that one on ebay, the EME-232 is the double density / dual sided version of the EME-156.
Speed adjustment is on motor, but it seem that the potentiometer is mounted upside down (white rubber hole), and can be damaged if forced or if the screwdriver is too wide.

Powered by SMFPacks Menu Editor Mod