Changes

Step-by-step instructions<BR>There are two ways to replace the CPC 464 ROM chip.<BR>

While everything is switched off and if you have the right set of tools and have any electrical knowledge, remove six screws from the keyboard and carefully take the keyboard a part. Look for = Step 1 =There are two ways to replace the CPC 464 ROM chip with the letters printed "IC103 AMSTRAD 40009" which is already soldered onto the motherboard. Here comes a real challenge.... <BR>

Firstly, * A. While everything is switched off and if you have to the right set of tools and have any electrical knowledge, remove additional nine screw using six screws from the keyboard and carefully take the keyboard a philips screwdriverpart. And then, you have to de-soldier all the legs from Look for the CPC 464 ROM chip, remove it and replace with [http://www.maplin.co.uk/p/dual-in-line-socket-28-pin-bl21x DIL Socket 28-Pin] (Maplin ref no: BL21X, the letters printed "IC103 AMSTRAD 40009" which it costs about 14p each - current price is now 44p each), making it easier to swap 464 or 6128 ROMs and visa versa, then solder all the legs from that socket already soldered onto the motherbaordmotherboard. Here comes a real challenge....<BR>

NextFirstly, put you have to remove additional nine screw using a philips screwdriver. And then, you have to de-soldier all the legs from the CPC 6128 464 ROM chip printed "AMSTRAD 40025 8902 B" inside the , remove it and replace with [http://www.maplin.co.uk/p/dual-in-line-socket-28-pin-bl21x DIL Socket 28-way socket. Put all the bits into placePin] (Maplin ref no: BL21X, put the keyboard cover back on and then put six screws back onwhich it costs about 14p each - current price is now 29p each or can be purchased from [https://www. Now to test your handy workebay.co.uk/sch/i. After your computer powered up with all accessorieshtml?_from=R40&_sacat=0&_nkw=DIL+Socket+28-Pin&_sop=15 eBay]), your screen should show exactly the same as CPC making it easier to swap 464 or 6128 start-up screenROMs and visa versa, then solder all the legs from that socket onto the motherbaord.<BR>

NOTENext, put the CPC 6128 ROM chip printed "AMSTRAD 40025 8902 B" inside the DIL 28-way socket. Put all the bits into place, put the keyboard cover back on and then put six screws back on. Now to test your handy work... After your computer powered up with all accessories, your screen should show exactly the same as [[Media: Cpc6128.gif|CPC 6128 start-up]] screen.<BR>

 '''NOTE:''' All versions of [http://www.old-computers.com/museum/computer.asp?st=1&c=84 CPC 464] keyboards including Arnold 1 (according to [http://genesis8.free.fr/amstrad/faq/amstrad.php#A comp.sys.amstrad.8bit FAQ]) version with big "AMSTRAD" letters printed onto the keyboard, like the one shown on the [http://www.old-computers.com/museum/photos/s_amstrad_464_inside1.jpg photo] - #'''12''': 32 Kb ROM memory containing the operating system and Locomotive Basic. Also with the "[http://cpctech.cpc-live.com/docs/costdown.html Cost-Down]" version as well doesn't have a socket to remove and replace Operating System ROM chips, instead all the legs are soldiered on and its impossible to remote it straight away, unless you know how to de-soldier - 31/6/05.<BR>

* B. Simply exchange your CPC 464 keyboard to Amstrad Specialist ([https://web.archive.org/web/20100201160217/http://www.midnight.uk.com:80/merline/ ArthurCook]) for another CPC 464 keyboard with CPC 6128 ROM chip fitted. (That's what I did on 12with [[User:Jonathanen#17th_June_2000.2A_-10-00, by the way_expanded_to_CPC_6128_spec._.2821.29|mine]] on Thursday 12th Oct 2000, as while I was rushing to get home from Worthing and that time, I didn't know how to replace Operating System ROMs) or ask him to do it for you and paid for it, of course. <BR> 

= Step 2 =Now you have a choice to do one of the following options:<BR> <BR> * A. Replace the [[AMSDOS ]] / CP/M bootstrap ROM with ParaDos [[ParaDOS]] ROM inside the disc interface (optional, but it allows you to use the full capacity on 3.5" disc drive), .<BR>'''RECOMMENDED''' to do so, if you're using CPC 464+ or unexpanded CPC 464 with both DDI-1 3" and 3.5" external disc drives only.either:<BR>

* [[464Plus_Conversion#Jonathanen.27s_Easy_Way_To_464.2B_Conversion|Upgraded CPC 464+ to 6128+ spec]] <BR>* Unexpanded CPC 464 without CPC 6128 OS/BASIC ROM installed, having only both DDI-1 3" & 3.5" external disc drives connected.<BR>To do that, you must remove six two screws first, open the cover, carefully remove the [[AMSDOS ]] ROM chip with "AMSTRAD 40009" printed on top of it and replace it with ParaDos [[ParaDOS]] ROM. Then put the cover back on, and put the six two screws back on.<BR><BR>* B. Leave the [[AMSDOS]] / CPM bootstrap ROM inside the [[Media:Gerald_DDI-1_MF0004B.jpg|disc interface]] (if you want to use DR. LOGO 2 & 3 on upgraded CPC 464) and put [[ParaDOS]] ROM inside the [[Rombo_Rombox|Rombo ROMBOX]] with other ROMS (as shown in [[Expanding_from_CPC_464_to_CPC_6128_Spec#Step_3|step 3]]).<BR>

Leave = Step 3 = Connect all the peripherals to "[[Connector:Expansion_port|Expansion]]" port connector (located at the back of the keyboard) in the following order:<BR><BR>* [[Dk'tronics_memory_expansion|DK'tronics 64K RAM pack Memory Expansion]] (removable RAM chips) >> upgraded to [[Media:Upgraded64kRAM.JPG|256K]] - [[Upgrading_a_Dk%27tronics_RAM_Expansion|instructions]]* [[Rombo_Rombox|Rombo ROMBOX]] with following ROMS from RAM pack pass-through connector - '''OPTIONAL!!''' But it makes computing much easier, leaving out both slots 0 ([[BASIC]]) & 7 ([[AMSDOS / CPM bootstrap ]]) remaining unused: <BR>:* Slot 1: [[BCPL]] - Compiler from PJB & [[Arnor|Arnor Ltd.]]:* Slot 2: [[Maxam]] - Assembler from [[Arnor|Arnor Ltd.]] :* Slot 4: [[ParaDOS]] - '''***''' '''ONLY!!''' If you choose to leave [[AMSDOS]] ROM chip inside the [[Media:Gerald_DDI-1_MF0004B.jpg|disc interface]] as mentioned in step 2B '''***''' :* Slot 5: [[Protext]] - Word processor from [[Arnor|Arnor Ltd.]] :* Slot 6: [[Utopia]] - General purpose utilities* [[Amstrad_Disk_Drive|Amstrad DDI-1 External 3" Disc Drive]] with Disc interface (if you want a choice of either replaced with [[ParaDOS]] ROM - '''recommended''' to use do it for [[464Plus_Conversion#Jonathanen.27s_Easy_Way_To_464.2B_Conversion|upgraded CPC 464+ to 6128+ spec]] or leave the [[AMSDOS]] ROM inside the disc interface - for using DR. LOGO 2 & 3 on upgraded CPC 464to 6128 spec, '''NOT''' [[464Plus_Conversion#Jonathanen.27s_Easy_Way_To_464.2B_Conversion|upgraded 464+]]) and put ParaDOS ROM inside from the Rombo pass-through connector on the [[Rombo_Rombox|ROMBOX ]]* 3.5” External disc drive with other ROMS (as shown below)external power supply, [[Side Select Switch|side switch]], [[Adding_3. Connect all the peripherals to 5"Expansion_drive_to_CPC464#3.5.22_READY_Signal_Test|" READY" signal]], DI-2 Inter-connecting Lead & [http://www.ebay.co.uk/itm/5Pcs-2-54mm-2x17-Pin-34-Pin-IDC-Male-Box-Header-Cable-Connector-Mounting-Ear-/172302047820?hash=item281e009a4c:g:KJkAAOSwl5dZdv-I 34 way IDC Male connector ] (34 pins sticking out) onto drive B connector on disc interface (located at the back of the keyboardDDI-1) in the following orderand place this disc drive on top of DDI-1 external disc drive - if you not sure how to, then follow "[http://www.cpcwiki.eu/index.php/Adding_3.5%22_drive_to_CPC464 Adding 3.5" Disc Drive 'B' - For CPC 464 Series with DDI-1 only!!]" instructions.<BR><BR>

DK= Step 4 =Follow the [[Adding_3.5"_drive_to_CPC464#3.5.22_READY_Signal_Test|"READY" signal]] instructions (if necessary) for 3.5" disc drive Ready signal test.<BR><BR>After all that, your fully expanded Amstrad CPC 464 to CPC 6128 spec set-up should look similar like this as shown below: <BR><BR>[[Image:CPC46426128setup.jpg|thumb|600px|centre|Upgraded Amstrad CPC 464 with available add-ons: CPC 6128 OS/BASIC ROM Chip replaced inside CPC 464 keyboard, Dk'tronics 64K RAM pack (upgraded to 256K), Rombo Rombox containing Utopia, BCPL, Maxam, Protext & ParaDos, Amstrad DDI-1 External 3" Disc Drive with removable RAM chipsAMSDOS / CP/M bootstrap ROM inside Disc Interface & modified 3.5" second External Disc Drive (NEC FD1036 A) with side switch, if you're very luckyREADY signal, built in power supply & Inter-connecting Lead with 34 way IDC Male connector.]]<BR>Now you can easily upgraded it have a choice to 256Kplay games or save / load programs from tape, either 3” or 3.5” discs! As software is concerned, its the same as CPC 6128 with a few add-ons included. <BR><BR>

Rombo ROMBOX with the following ROMS = Note =<BR>This idea originally comes from [http://www.obsoletecomputermuseum.org/amstrad/ David Cantrell's CPC 464] at [http://www.obsoletecomputermuseum.org Obsolete Computer Museum] but he didn't write out the pass-through connector instructions how to do it like I did. Its took me months of research to work out how it works on my own CPC 464 one by one and writing it out on rough paper, after I have looked at his web site for the RAM pack (OPTIONALfirst time and thinking that "Wow!! But That's what I always wanted on my CPC 464" while I was searching for Amstrad CPC 464 Specs on Internet. Now its here on this web site and I'm very proud that it makes computing more easier) Utopia v 1works perfectly on my expanded CPC 464.25<BR>Maxam v 1<BR>[[Image:CPC46426128_dualROM.25Protext v JPG|thumb|600px|centre|Another upgraded Amstrad CPC 464 except with dual Amstrad CPC 464 & CPC 6128 OS/BASIC ROM Chips fitted inside older CPC 464 keyboard, a 464 / 6128 Mode switch on left hand side and 2 x 3" FD-1.22BCPL v drives (DDI-1.0or ParaDos v 0.50 as well ) - only, if you choose to leave the AMSDOS purchased from eBay on 4th March 2012. Both PARADOS ROM chip replaced inside the disc interface& Dk'tronics 64K RAM pack (SMD version) wasn't included in the part of the package and it was purchased separately.]]

3.5” external disc drive with external power supply, [[Side Select Switch|Side Switch]], READY signal and a drive lead with 34 way IDC Male connector (34 pins sticking out) to the back of DDI-1 disc interface and place this disc drive on top of DDI-1 external disc drive - if you not sure how to, then follow <gallery caption="[http://www.cpcwiki.eu/index.php/Adding_3.5%22_drive_to_CPC464|Adding 3.5Archives" Disc Drive 'B' - For CPC 464 Series with DDI-1 only!!]" instructions.>

Now you have * [https://www.retrocomputers.online/2012/06/amstrad-cpc464-upgraded-to-a choice -cpc6128-how-to play games or load programs on tape, either 3” or 3/ How to convert a Amstrad CPC464 into a CPC6128 | Retro Computers]<BR>* [https://www.5” discs! As software is concerned, its retrocomputers.online/2012/06/how-to-install-parados-into-the same as -amstrad-dd-1-disk-interface/ How to install PARADOS into the Amstrad DDI-1 disk interface | Retro Computers]<BR>* [http://www.eightbitmagazine.com/cpcoxygen/magazine/01/super464/super464.htm Super 464 | CPC 6128 with a few addOxygen]<BR>* [http://www.freetimeweb.nl/home/computer/cpc/cpc_464_extended_uk.html THE AMSTRAD / SCHNEIDER CPC EXTENDED]<BR>* [http://www.indieretronews.com/2014/06/amstrad-ddi-1-clone-latest-ons includedinterface. html Amstrad DDI-1 clone - The latest interface device for the Amstrad CPC 464 on Steve Netting's Amstrad 464]<BR> * [http://www.theregister.co.uk/Print/2014/02/12/archaeologic_amstrad_cpc_464/ You’re NOT fired: The story of Amstrad’s amazing CPC 464 • The Register]<BR>Note* [http://www.retrogamer.net/profiles/hardware/amstrad-cpc-6128/ Amstrad CPC 6128 | Retro Gamer]<BR>* [[Amstrad Action]] ([[Amstrad_Action,_Issue_30,_Mar_1988|Issue 30, March 1988]]) - [[:File:AmstradAction030-26.jpg|page 26]]

[http[Category://www.retrocomputers.eu/2012/06/25/amstrad-cpc464-upgraded-to-a-cpc6128-how-to/ How to convert a Amstrad CPC464 into a CPC6128. | Retro ComputersHardware]]