Upgrade of [[Category:DIY]] [[Category:Memory expansions]]A project to upgrade a CPC6128 to 512K RAM (total), done by replacing the CPC 6128CPC6128's internal RAM to 512 KiB as proposed in chips, and its PAL banking chip, the article '''Aus David wird Goliath: 512 KB RAM für Schneider CPC''' project was released 1987 in issue 10/1987, pages 156 to 162 of the German IT german magazine '''c'tMagazin'''. The DIY project name is '''CPC 6512'''. The mod requires to remove (or disable) the sixteen RAM chips on the CPC6128 mainboard, and to replace them by bigger chips, plus whatever additional bank selection logic.
One issue later, c't 11/1987, the magazine published a driver which creates a RAM disk within the additional memory. This RAM disk can be used in [[AMSDOS]]. == The Circuit ==
== Technical ==* '''DRAM Replacement''' - Replace the sixteen old 64Kx1 DRAM chips (IC119-IC134) by new 256Kx1 DRAMs. The chips have same pinouts, only pin 1 is changed (old: NC, new: A8 row:column address signal). Optionally, replace only bank 0 (IC127-IC134) for getting only 320K (256K+64K) instead of 512K total (2x256K).
The memory is accessed via Port 7Fxxh, as on [[Standard Memory Expansions]]* '''PAL Replacement''' - Replace the old PAL (IC118) by the new daughterboard. Since Most signals connect to the internal RAM is removed, its total capacity is only 512K PAL socket (unlike standard 512K expansions which provide 64K internal plus 512K external memorygreen in schematic), ie. 576K totala extra few wires connect elsewhere on mainboard (red). Altogether, as an optional "bonus" feature, the c't expansion works like circuit contains logic for a 448K dk'tronics expansion 3rd floppy drive (leaving the banks selected via OUT [7Fxxh],FCh..FFh unusedblue).
One half (256K) of the total (512K) expansion memory can be accessed as Video RAM (with normal expansions, only 64 KB are accessible as VRAM)<gallery>File:CPC6512 ct magazin schematic. This is making the expansion slightly incompatible with the dk'tronics standard. However, usually expansion memory is mapped to 4000h-7FFFh, whilst VRAM is usually mapped to C000h-FFFFh. So, most existing software may work with it, without accidently displaying garbage on the screenpng|SchematicFile:CPC6512 ct magazin pcb.jpg|PCB</gallery>
== Missing Info =='''Component List''' 16x 41256 (256Kx1 DRAM) ;replacing the CPC6128's 16 built-in 64Kx1 DRAMs 1x PAL 16L8 ;replacing the CPC6128's built-in PAL 1x 74LS38 ;Quad 2-input NAND, OC 1x 74LS273 ;8bit latch, of which only 5bit are used here 1x 2200 Ohm resistor ;pull-up for OC output 1x 470 Ohm resistor ;pull-up for OC output 1x 47 Ohm resistor ;purpose unknown (noise related? shortcut protection?)
* Unknown which banks are usable as VRAM** The first four 16K bank are (probably) usuable as VRAM (as on all 64K CPC models)** The next four 16K bank are (hopefully) not usuable as VRAM (for CP/M+ compatibility, which uses them as Work RAM)** For further banks it's totally unknown if they are used as VRAM or not* Unknown if it's fully dk'tronics compatible, or more like incompletely implemented Inicron variant* Unknown what happens on accessing the unused region via OUT [7Fxxh],FCh..FFh* Chipset / Schematic is unknown== Compatibility Problems ==
== Scanned Article / Schematics ==* RAMDIS is not supported, not a problem in most cases, but won't work with some special types of expansion hardware, like [[Multiface II]].* The expansion seems to have been designed independently of [[Standard Memory Expansions]] like the dk'tronics one. So, there is no (intended) compatibility. However, both c't and dk'tronics are designed around the CPC6128 banking mechanism, so they do work similar in some ways. Namely, both can map expansion banks to 4000h..7FFFh, but there are several differences:** For the mapping to 4000h..7FFFh, dk'tronics uses values CCh..CFh, D4h..C7h, DCh..DFh, ... FCh..FFh whilst c't uses values C8h..DFh. Some of these values do overlap, resulting in some (unintended) semi-compatibility, but there's still one big difference: along with the above values, dk'tronics maps bank 3 to C000h..FFFFh, whilst c't maps bank 7 to that region.
<gallery>Image:NoPicture.gif|c't, issue 10/1987 (RAM schematic)Image:NoPicture.gif|c't, issue 11/1987 (RAM disc driver)</gallery>== Memory Configurations ==
== Offtopic ==The memory is controlled by OUT [7Fxxh],C0h..DFh instructions. Values C0h..C7h are working same as on normal CPC6128s. Values C8h..DFh do access the additional RAM banks (C8h..D3h when using the cut-down 320K upgrade variant).
The OUT [7Fxxh],C0h+... 0 1 2 3 4 5 6 7 8..31 ------------------------------------------------------- Bank at C000h..FFFFh 3 7 7 7 3 3 3 3 7 (!) Bank at 8000h..BFFFh 2 2 6 2 2 2 2 2 2 Bank at 4000h..7FFFh 1 1 5 3 4 5 6 7 8..31 Bank at 0000h..3FFFh 0 0 4 0 0 0 0 0 0 == PAL Source Code == Below is a typed-up and commented copy of the PALASM source code from the original article. D7D6 D0 D3 D4 D1 D2 NCAS A15 A14 GND ;pin 1..10 CPU A15S AMUX MUX LCLK CAS1 CAS0 IOWR A14S VCC ;pin 11..20 IF (VCC) /LCLK= D7D6 * /A15 * /IOWR ;load external latch on OUT [7Fxxh],C0h..FFh IF (VCC) /CAS0= /NCAS * /D4 + ;bank bit4=0, select bank 0..15 (CPU and CRTC) /CAS0= /NCAS * A15 + /CAS0= /NCAS * /A14 + /CAS0= /NCAS * CPU IF (VCC) /CAS1= /NCAS * D4 * /A15 * A14 * /CPU ;bank bit4=1, select bank 16..31 (CPU at 4000h..7FFFh only) IF (VCC) /A14S= /A14 + ;bank bit0 /D0 * D2 * /A15 + /D0 * D3 * /A15 + /D0 * D4 * /A15 IF (VCC) /A15S= /A14 * /A15 + ;bank bit1 /D1 * /A15 + /D4 * /D3 * /D2 * /D0 * /A15 + /D4 * /D3 * /D2 * /D1 * /A15 IF (VCC) /AMUX= /D0 * D1 * /D2 * /D3 * /D4 * /CPU * /MUX + A15 * A14 * /D2 * D0 * /CPU * /MUX + A15 * A14 * /D2 * D1 * /CPU * /MUX + A15 * A14 * D3 * /CPU * /MUX + A15 * A14 * D4 * /CPU * /MUX + /A15 * A14 * D2 * /CPU * /MUX + ;bank bit2 /A15 * A14 * D3 * /CPU * MUX ;bank bit3 IF (GND) /MUX = /MUX ;dummy (do not output anything on this pin) IF (GND) /IOWR=/IOWR ;dummy (do not output anything on this pin) '''CPC 6512Note:''' c't ''Memory ExpansionFor VRAM access, bank bits 2,3,4 are forced to zero (by above formulas), bank bit 0,1 are coming from the CRTC, passed directly to IC109 (without going through the PAL), so, the RAM banking affects only the CPU's memory accesses, not the CRTC' s video memory accesses. Some notes on the syntax:* The first two lines assign the pin-outs. Observe that leading "/" slashes are omitted here. For example, "/CPU" (in schematic) becomes "CPU" (in source code). Accordingly "/CPU" (in source code) would be double-negated "//CPU" aka "CPU" (in schematic).* The "IF (condition) signal=" part means that "signal" becomes an output when condition is not true. In the above source code, condition is always true (VCC), or, for the last 2 lines, always false (GND).* The "*" and "+" operators are meaning "* = AND", "+ = OR". The idea behind that confusing syntax was to make it "easier" to learn for people who are trained only in basic maths (the formulas do also work when treating *=multiply, and +=plus. For example: 1+0+1+1 = 3 = nonzero = true).* There must be confused with issues some priority ordering in the formulas: Either * before +, or operations inside of a line before merging the results of the separate lines (in above examples, both ordering methods do work). == Scanned Article / Schematics == * [[Media:CPC6512 ct magazin part 1.pdf]] - c't issue 10/1987 - RAM Expansion Schematic* [[Media:CPC6512 ct magazin part 2.pdf]] - c't issue 11/1987 - RAM Disc driver for CP/M Plus Original names of the articles are: '''Aus David wird Goliath: 512 KB RAM für Schneider CPC 6512''' (part 1), and '''CPC 6513Byte-Hirte: RAM-Disk-Treiber für des CPCs 512 Kbyte''' of the more popular ''World War II Fanzine'' from Concord Publications Company(part 2).<gallery>File:Cpc6512Both articles are written by Gabor Herr and Hubert Schröer.jpg|CPC 6512File:Cpc6513.jpg|CPC 6513</gallery>
== Related hardware modifications ==
* [http://cpcwiki.eu/forum/index.php/topic,662.msg7113.html#msg7113 Bank exchange toggle Swapper by Khany/Cherry-T] (less complex: bank-exchanging toggle, no memory expansion; 1993)
* [[CPC4MB| CPC4MB memory upgrade by Yarek]] (more advanced; 2005/2006)
