* The ''This is an article about the "'CRTC''' (Cathode Ray Tube Controller" hardware unit ) helps to generate the video signal of the Amstrad CPC. For the cpc scene member see [[ChaRleyTroniC]]''
NOTE: This document describes the functionality in terms of the CPC with its separate CRTC and Gate-Array. The '''Plus has both integrated into the same IC, but could be considered to have two functional blocks, one for CRTCand one for Gate-Array. In this document the term 'Gate-Array'' (Cathode Ray Tube Controller) generates is used, but this also applies to the video signal of the Amstrad CPCASIC.
== Overview ==
== Type 2 - MC6845 / MC6845P ==
== Type 3 - The ASIC ==
== Type 4 - PreASIC ==
== Programming the CRTC ==
The 6845 Cathode Ray Tube Controller (CRTC)
Introduction
The 6845 Cathode Ray Tube Controller (CRTC) is a programmable IC used to generate video displays. This IC is used in a variety of computers including the Amstrad CPC, Amstrad CPC+ and KC Compact.
CRTC in the Amstrad CPC/CPC+ and KC Compact designs
The CRTC was a common part available from many different manufacturers. During the life of the CPC, Amstrad sourced the CRTC from various manufacturers.
1. The CRTC functionality is integrated into the CPC+ ASIC. This type exists only in the CPC464+,CPC6128+ and GX4000.
2. This type exists in "cost-down" CPC464 and CPC6128 systems. In the "cost-down" the CRTC functionality is integrated into a single ASIC IC. This ASIC is often refered to as the "Pre-ASIC" because it preceeded the CPC+ ASIC. The CRTC functionality of the Pre-ASIC is almost identical to the CRTC within the ASIC.
3. In the Amstrad community each 6845 implementation has been assigned a type number. This type identifies a group of implementations which operate in exactly the same way.
It is possible to detect the 6845 present using software methods, and this is done to:
* warn that the software was not designed for the detected 6845 and may function incorrectly, * to adapt the software so that it will run with the detected 6845 * In most cases, the type of the detected 6845 is reported.
4. As far as I know, the KC compact used HD6845R only.
4. As far as I know, the KC compact used HD6845S only. == Timings and relating with Z80 instructions count ==
The 6845 is selected when bit 14 of the Some informations like : how many Z80 instructions can Ifit within a scan line ? Within a screen ? Etc... See http:/O port address is set to "0"/www. Bit 1 cpcwiki.eu/forum/programming/frame-flyback-and 0 of the I-interrupts/O port address define the function to access. The remaining bits can msg25106/#msg25106(To be any value, but it is adviseable to set these extracted/edited to "1" conform to avoid conflict with other devices in the systemwiki good practices).
==Programming==
The 6845 is selected when bit 14 of the I/O port address is set to "0". Bit 9 and 8 of the I/O port address define the function to access. The remaining bits can be any value, but it is adviseable to set these to "1" to avoid conflict with other devices in the system.
The recommended I/O port addresses are
'''NOTE'''
1. The function of these I/O ports is dependant on the CRTC type Signals
2. If you perform an IN instruction to the select or write functions it will write data to the CRTC from the current data on the bus.
|''Memory Address Signal''||''Signal source''||''Signal name''
|-
|A15||6845||MA12 MA13
|-
|A14||6845||MA11 MA12
|-
|A13||6845||RA2
CRTC generates the address, Gate-Array reads the data and converts it to pixels based on the current mode.
CRTC pins RA3, RA4, MA10, MA11 are not connected on CPC.
== CUDISP ==
CUDISP signal defines the hardware cursor.
CRTC pin CUDISP is not connected to the Gate Array, so it has no effect on a barebone CPC or Plus machine.
However, this signal is provided to the expansion port. And it is used by the [[PlayCity]] and [[Play2CPC]] expansions.
== DISPTMG ==
DISPTMG signal defines the border. When DISPTMG is "1" the border colour is output by the Gate-Array to the display. The DISPTMG can be forced using R8 (DISPTMG Skew) on type 0,3 and 4 or by setting R6=0 on type 1. It is not possible to force the DISPTMG on type 2. The border has higher priority than pixels but lower priority than the black colour output when HSYNC/VSYNC are active.
== HSYNC and VSYNC ==
On CPC, HSYNC and VSYNC from the CRTC are passed into the Gate-Array. The When HSYNC is active Gate-Array modifies outputs the signals and palette colour black. If the HSYNC is set to 14 characters then mixes these black will be output for 14us. The HSYNC is modified before being sent to form the Composite-Sync which monitor. It happens 2us after the HSYNC from the CRTC and lasts 4us when HSYNC length is greater or equal to 6. If R2=46, and HSYNC width is 14 then monitor hsync starts at 48 and lasts until 51. On a CPC monitor, the HSYNC is rendered in "absolute black". It is darker than the black output by the Gate-Array. The VSYNC is also modified before being sent to the display monitor. It happens two lines* after the VSYNC from the CRTC and stay two lines (same cut rule if VSYNC is lower than 4). PAL (50Hz) does need two lines VSYNC_width, and 4us HSYNC_width. CRTCs 1 and 2 have a fixed VSYNC width value of 16. VSYNC width can be configured with Register 3 on CRTCs 0, 3 and 4. The 6845 Designbit 0 of port B of the PPI changes to 1 as soon as the VSYNC signal is produced by the CRTC. == The 6845 Registers==
== The Internal registers of the 6845 are == :
{|{{Prettytable|width: 700px; font-size: 2em;}}
|''Register Index''||''Register Name''||''Range''||''CPC Setting''||''Notes''
|-
|0||Horizontal Total(-1)||00000000||63||Width of the screen, in characters. Should always be 63 (64 characters). 1 character == 1μs.
|-
|1||Horizontal Displayed||00000000||40||Number of characters displayed. Once horizontal character count (HCC) matches this value, DISPTMG is set to 1.
|-
|2||Horizontal Sync Position||00000000||46||When to start the HSync signal.
|-
|3||Horizontal and Vertical Sync Widths||VVVVHHHH||128+14||HSync pulse width in characters (0 means 16 only on some CRTC), should always CRTCs. Needs to be more than 8at least 2 for Gate Array to change the video mode); VSync width in scan-lines. (0 always means 16 on some CRTC. Not present on all CRTCs, fixed to 16 lines on these).
|-
|4||Vertical Total(-1)||x0000000||38||Height of the screen, in characters.
|-
|5||Vertical Total Adjust||xxx00000||0||Measured in scanlines, can be used for smooth vertical scrolling on CPC.
|6||Vertical Displayed||x0000000||25||Height of displayed screen in characters. Once vertical character count (VCC) matches this value, DISPTMG is set to 1.
|-
|7||Vertical Sync positionPosition||x0000000||30||When to start the VSync signal, in characters.
|-
|8||Interlace and Skew||xxxxxx00CCDDxxII||0||00CC: No interlace; 01Cursor Skew (Only in CRTCs 0, 3 and 4). DD: Interlace Sync Raster Scan Mode; 10Display Skew (Only in CRTCs 0, 3 and 4). II: No Interlace; 11: Interlace Sync and Video Raster Scan Mode.
|-
|9||Maximum Raster Address(aka Number of Scan Lines) (-1)||xxx00000||7||Maximum scan line address on CPC can hold between 0 and 7, higher values' upper bits are ignored
|-
|10||Cursor Start Raster||xBP00000||0||Cursor signal is not used on CPCconnected to the Gate Array but is provided to the expansion port. B = Blink On/Off; P = Blink Period Control (Slow/Fast). Sets first raster row of character that cursor is on to invert.
|-
|11||Cursor End Raster||xxx00000||0||Sets last raster row of character that cursor is on to invert
|-
|12||Display Start Address (High)||xx000000||3248||On Amstrad Plus, bit7 of the printer port is controlled by bit3 of CRTC R12 (ie. bit11 of Display Start Address)
|-
|13||Display Start Address (Low)||00000000||0||Allows you to offset the start of screen memoryfor hardware scrolling, useful when and if using memory from address &0000with the firmware.
|-
|14||Cursor Address (High)||xx000000||0
|-
|15||Cursor Address (HighLow)||00000000||0
|-
|16||Light Pen Address (High)||xx000000||||Read Only. On CRTC1, bit6 of Status register goes to 0 when R16 is read
|-
|17||Light Pen Address (HighLow)||00000000||||Read Only. On CRTC1, bit6 of Status register goes to 0 when R17 is read
|-
|}
registers 18-31 read as 0, on type 0 and 2.
registers 18-30 read as 0 on type1, register 31 reads as 0xff.
Details about Reg. 12 and Reg. 13 specifically:
.------- REG 12 --------. .------- REG 13 --------.
| | | |
15 14 13 12 11 10 09 08 07 06 05 04 03 02 01 00
.--.--.--.--.--.--.--.--. .--.--.--.--.--.--.--.--.
|X |X | | | | | | | | | | | | | | | |
'--'--'--'--'--'--'--'--' '--'--'--'--'--'--'--'--'
'--.--'--.--'---------------.-----------------'
| | |
| | '------> Offset for setting
| | videoram
| | (1024 positions)
| | Bits 0..9
| |
| '-------------------------> Video Buffer : note (1)
|
'-------------------------------> Video Page : note (2)
note (1) note (2)
.--.--.--------------. .--.--.---------------.
|11|10| Video Buffer | |13|12| Video Page |
|--|--|--------------| |--|--|---------------|
| 0| 0| 16Ko | | 0| 0| 0000 - 3FFF |
|--|--|--------------| |--|--|---------------|
| 0| 1| 16Ko | | 0| 1| 4000 - 7FFF |
|--|--|--------------| |--|--|---------------|
| 1| 0| 16Ko | | 1| 0| 8000 - BFFF |
|--|--|--------------| |--|--|---------------|
| 1| 1| 32Ko | | 1| 1| C000 - FFFF |
'--'--'--------------' '--'--'---------------'
So, it's possible to use 32KB screen size (used for [[Programming:Overscan|overscan]]) by setting bits 11 and 10 both to 1 (of Register 12). Bits MA11 and MA10 of the address generated by the CRTC are not written on the address bus to access video memory; settings both bits to 1 is the only way to cause a carry to bit MA12 when address pass over the end of current video page to change the memory address to the next video page.
== CRTC Differences ==
|1||0||-||-
|-
|1||1||Read from selected internal 6845 register||Read only Only
|-
|}
|1||0||Read Status Register||Read Only
|-
|1||1||Read from selected internal 6845 register||Read only Only
|}
|1||0||-||-
|-
|1||1||Read from selected internal 6845 register||Read only Only
|-
|}
|1||0||Read from selected internal 6845 register||Read Only
|-
|1||1||Read from selected internal 6845 register||Read only Only
|-
|}
{|{{Prettytable|width: 700px; font-size: 2em;}}
|rowspan=2|''Register Index''||rowspan=2|''Register Name''||colspan=43|''Type''
|-
|0||1||& 2||3||& 4
|-
|0||Horizontal Total(-1)||Write Only|colspan=3 style="text-align: center;"|Write Only||Write Only||(note 2)||(note 3)
|-
|1||Horizontal Displayed||Write Only|colspan=3 style="text-align: center;"|Write Only||Write Only||(note 2)||(note 3)
|-
|2||Horizontal Sync Position||Write Only|colspan=3 style="text-align: center;"|Write Only||Write Only||(note 2)||(note 3)
|-
|3||Horizontal and Vertical Sync Widths||Write Only|colspan=3 style="text-align: center;"|Write Only||Write Only||(note 2)||(note 3)
|-
|4||Vertical Total(-1)||Write Only|colspan=3 style="text-align: center;"|Write Only||Write Only||(note 2)||(note 3)
|-
|5||Vertical Total Adjust||Write Only|colspan=3 style="text-align: center;"|Write Only||Write Only||(note 2)||(note 3)
|-
|6||Vertical Displayed||Write Only|colspan=3 style="text-align: center;"|Write Only||Write Only||(note 2)||(note 3)
|-
|7||Vertical Sync positionPosition||Write Only|colspan=3 style="text-align: center;"|Write Only||Write Only||(note 2)||(note 3)
|-
|8||Interlace and Skew||Write Only|colspan=3 style="text-align: center;"|Write Only||Write Only||(note 2)||(note 3)
|-
|9||Maximum Raster Address(aka Number of Scan Lines) (-1)||Write Only|colspan=3 style="text-align: center;"|Write Only||Write Only||(note 2)||(note 3)
|-
|10||Cursor Start Raster||Write Only||Write Only||Read/Write Only||(note 2)||(note 3)
|-
|11||Cursor End Raster||Write Only||Write Only||Read/Write Only||(note 2)||(note 3)
|-
|12||Display Start Address (High)||Read/Write||Write Only||Write Only||Read/Write (note 2)||(note 3)
|-
|13||Display Start Address (Low)||Read/Write||Write Only||Write Only||Read/Write (note 2)||(note 3)
|-
|14||Cursor Address (High)||Read/Write|colspan=3 style="text-align: center;"|Read/Write||Read/Write||Read/Write (note 2)||(note 3)
|-
|15||Cursor Address (Low)||Read/Write|colspan=3 style="text-align: center;"|Read/Write||Read/Write||Read/Write (note 2)||(note 3)
|-
|16||Light Pen Address (High)||Read Only|colspan=3 style="text-align: center;"|Read Only||Read Only||Read Only (note 2)||(note 3)
|-
|17||Light Pen Address (HighLow)||Read Only|colspan=3 style="text-align: center;"|Read Only||Read Only||Read Only (note 2)||(note 3)
|-
|}
'''Notes'''
1. On type 0 * The CRTC is not connected to the CPU's RD and 1WR pins, so the CRTC is not aware of the CPU bus I/O direction. Therefore, if a Write Only register is read frominstruction is used on a write register of the CRTC, "0" then a data is returnedsent to the CRTC.
2. See the document * On types 0 and 1, if a Write Only register is read from, "Extra CPC Plus Hardware Information0" for more detailsis returned.
* CRTC types 3and 4 are identical in every way, except for the unlocking mechanism, split-screen and 8-bit printer port functionalities specific to the ASIC. * See the document "Extra CPC Plus Hardware Information" for more details. === Horizontal and Vertical Sync (R3) === Type 0:*Bits 7.. CRTC type 4 define Vertical Sync Width. If 0 is programmed this gives 16 lines of VSYNC.*Bits 3..0 define Horizontal Sync Width. If 0 is programmed no HSYNC is generated. Type 1:*Bits 7..4 are ignored. Vertical Sync is fixed at 16 lines.*Bits 3..0 define Horizontal Sync Width. If 0 is programmed no HSYNC is generated. Type 2:*Bits 7..4 are ignored. Vertical Sync is fixed at 16 lines.*Bits 3..0 define Horizontal Sync Width. If 0 is programmed this gives a HSYNC width of 16. Types 3/4:*Bits 7..4 define Vertical Sync Width. If 0 is programmed this gives 16 lines of VSYNC.*Bits 3..0 define Horizontal Sync Width. If 0 is programmed this gives a HSYNC width of 16. === Interlace and Skew (R8) === Types 0/3/4:*Bits 7..6 define the same as skew (delay) of the CUDISP signal (00 = Non-skew ; 01 = One-character skew ; 10 = Two-character skew ; 11 = Non-output).*Bits 5..4 define the skew (delay) of the DISPTMG signal (00 = Non-skew ; 01 = One-character skew ; 10 = Two-character skew ; 11 = Non-output).*Bits 3..2 are ignored.*Bits 1..0 define the interlace mode (00 = No Interlace; 01 = Interlace Sync; 10 = No Interlace; 11 = Interlace Sync and Video). Types 1/2:*Bits 7..2 are ignored.*Bits 1..0 define the interlace mode. Interlace modes: [[File:CRTC type Interlace modes.png]] === UM6845R and R31 === R31 is described in the UM6845R documentation as "Dummy Register". Its use is described in the documentation for the Rockwell R6545 in combination with R18, R19 and R8 and the Status Register. In the UM6845R it appears to have no effect. Reading and writing does nothing. Reading it returns 0x0ff. R31 doesn't exist on types 0,2,3,4. === UM6845R and R12/R13 === The UM6845R differs to other CRTC in respect of R12/R13. When VCC=0, R12/R13 is re-read at the start of each line. R12/R13 can therefore be changed for each scanline when VCC=0. Just like other CRTCs when RC==(R9-1), the current MA is captured for the next char-line. In demos to make a display compatible with all CRTCs program R12/R13 when VCC!=0. This will then take effect at the next frame start. === UM6845R status register === The UM6845R has a status register that can be read using port &BExx. Bit 6 is set to 1 if there is a strobe input to the /LPEN signal. It is cleared to 0 when either R17 or R16 (LPEN address) of the CRTC are read. It signals there is a valid LPEN input. On my CPC (arnoldemu) with UM6845R, it is triggered at power on, R17 and R16 have the values 0 when read. Bit 5 is set to 1 when CRTC is in "vertical blanking". Vertical blanking is when the vertical border is active. i.e. VCC>=R6. It is cleared when the frame is started (VCC=0). It is not directly related to the DISPTMG output (used by the CPC to display the border colour) because that output is a combination of horizontal and vertical blanking.This bit will be 0 when pixels are being displayed. All the other bits read as 0 and don't have any function. === R10/R11 on ASIC/Pre-ASIC === The cursor raster registers also repeat R10/R11 act as they do status registers when read on Types 3 & 4. They behave as normal cursor raster registers upon write. {| class="wikitable sortable"! R10 - Bit number! Bit value! Event|-|0|1|C0=R0|-|1|0|C0=R0/2|-|2|0|C0=R1-1 (if R0>=R1)|-|3|0|C0=R2|-|4|0|C0=R2+R3|-|5|01|R3h>0 : C0=0..R0 on the type line R3h from Vsync (C4=R7)R3h=0 : C0=0..R0 over 15 lines from Vsync (C4=R7)|-|6|1|Always 1|-|7|00|C0=0..R0-1 : VMA.Lsb=0xFFC0=R0 : VMA'.Lsb=0x00 (same cond if C0=R0=0)|} {| class="wikitable sortable"! R11 - Bit number! Bit value! Event|-|0|0|C4=R4 and C9=R9 and C0=R0 : Last char of screen|-|1|0|C4=R6-1 and C9=R9 and C0=R0 : Last char displayed|-|2|0|C4=R7-1 and C9=R9 and C0=R0 : Last char before Vsync|-|3|0/1|Timer 16 CRTC frames|-|4|1|Always 1|-|5|0|C9=R9 : C0=0 to R0|-|6|0|Always 0|-|7|1|(C9=R9 and C0=R0) or (C9=0 and C0=0 to R0-1)|} === Reading from CRTC registers on ASIC/Pre-ASIC === On CRTC Types 3 and 4, only the 3 least significant bits of the selected register number are considered to read a register according to the following table: {|{{Prettytable|width: 700px; font-size: 2em;}}|'''Nb'''||'''Register'''||'''Definition'''|-|0||R16||Light Pen Address (High)|-|1||R17||Light Pen Address (Low)|-|2||R10||Cursor Start Raster|-|3||R11||Cursor End Raster|-|4||R12||Display Start Address (High)|-|5||R13||Display Start Address (Low)|-|6||R14||Cursor Address (High)|-|7||R15||Cursor Address (Low)|} Therefore, as an example, reading register 4 will give the same result as reading register 12 or 20. <br> == CRTC Type Detection ==<pre>10 MODE 1:' Reinitialize screen20 OUT &BC00,31:IF INP(&BF00)=255 THEN PRINT"crtc 1":END30 OUT &BC00,12:IF INP(&BF00)=0 THEN PRINT"crtc 2":END40 OUT &BC00,20:IF INP(&BF00)=0 THEN PRINT"crtc 0":END50 PRINT"crtc 3/4"</pre><br> == CRTC Timing Diagrams ==[[File:CRTC Timing Diagram Rockwell.png]] <br> [[File:CRTC timing small.gif]] <br> == Internal Counters =={| class="wikitable sortable"! Counter name! Abbr! Alternate name|-|Horizontal Character Counter|HCC|C0|-|Horizontal Sync Counter|HSC|C3l|-|Vertical Character Counter|VCC|C4|-|Vertical Sync Counter|VSC|C3h|-|Vertical Line Counter|VLC|C9|-|Vertical Total Adjust Counter|VTAC|C5 (or C9 on CRTCs 0/3/4)|-|Frame Counter|FC|''Used for interlace and CRTC cursor blinking''|} No matter its type, the CRTC never buffers its counters. The only value that is saved in a buffer in the CRTC is the video pointer because it is reloaded at each line start. <br> == Hitachi Block Diagram ==[[File:CRTC Block Diagram.png]] <br> == UMC Block Diagram ==[[File:UMC CRTC Block Diagram.png]] <br> == Motorola Block Diagram ==[[File:Motorola CRTC Block Diagram.png]] <br>
== Datasheets ==
* [[Media:hd6845.hitachi.pdf|HD6845 HD6845S (Hitachi) (aka type 0)]]* [[Media:Um6845.umcUM6845-UMC.pdf|UM6845 (UMC) (aka type 0)]]
* [[Media:Um6845r.umc.pdf|UM6845R (UMC) (aka type 1)]]
* [[Media:Mc6845.motorola.pdf|MC6845 (Motorola) (aka type 2)]] [[Media:Mc6845.pdf|Other datasheet version]]*[[Media:CRTC-5-HD6345.pdf|HD6345 (Hitachi) (aka type 5)]] Upgraded pin-compatible CRTC chip with advanced functionalities [https://thecheshirec.at/2024/05/07/un-crtc6345-sur-amstrad-cpc/ Upgrading the CPC to HD6345]
* [[VHDL implementation of the 6845]] == Clones Unused clones ==
* [CM607P a Bulgarian clone made in Pravetz factory]
* [EF6845P by Thomson Semiconductors]
* [UM6845E by UMC]
* [SY6845EA by Synertek]
* CRTC6545 (MOS, Rockwell, Synertek) is pin-compatible with the 6845 and only has minor differences
* [https://github.com/hoglet67/BeebFpga/blob/dev/src/common/mc6845.vhd BeebFpga] [https://github.com/MiSTer-devel/Amstrad_MiSTer/blob/master/rtl/UM6845R.v MiSTer] [https://opencores.org/websvn/filedetails?repname=System09&path=%2FSystem09%2Ftrunk%2Frtl%2FVHDL%2Fcrtc6845.vhd OpenCores] Verilog/VHDL implementations of the 6845
== Tools about CRTC ==
* [http://www.cpcwiki.eu/imgs/9/99/Elmar_Krieger-SPECIAL_EFFECTS.dsk some BASIC tools to detect CRTC types 0-1-2 and show some effects] by [[Elmar Krieger]] (DSK for Emulators)
* [[File:Shaker26.dsk]] Shaker - Suite of CRTC tests associated with the CPC CRTC compendium (many of them will not work correctly on emulators and that was the purpose of the tests, to help create more compatible emulation)
* [[File:Shaker addon.dsk]] Shaker Add-On (Pixel 1 Hard Scroll / Vertical Rupture all Crtc)
== Links ==
* [http://en.wikipedia.org/wiki/6845 Wikipedia on the CRTC]
* [http://www.grimware.org/doku.php/documentations/devices/crtc CRTCs on grimwareCRTC documentation from Grimware]* [http://quasar.cpcscene.net/doku.php?id=assem:crtc Quasar CRTC documentation (in french)]* [[Media:Dossier Rupture(Gozeur Paradox).pdf]]* [[Media:Dossier CRTC(Ramlaid Mortel).pdf]] Les entrailles du CRTC* [https://thecheshirec.at/tag/crtc6845/ Leçons CRTC (CheshireCat)]* [[Media:ACCC1.8-EN.pdf]] [[Media:ACCC1.8-FR.pdf]] CPC CRTC Compendium - Latest (04/2024!) document containing in-depth info about CRTC programming on CPC.
==Related pages==
*[[Video modes]]
*[[Synchronizing Synchronising with the CRTC and display]] : technic and details on the relationship between Gate Array and CRTC.
[[Category:Hardware]] [[Category:CPC Internal Components]] [[Category:Programming]] [[Category:Datasheet]] [[Category:Graphic]]