Difference between revisions of "Rombo Rombox"
(→Technical) |
|||
| (8 intermediate revisions by 7 users not shown) | |||
| Line 1: | Line 1: | ||
| − | A ROM expansion board | + | A ROM expansion board from [[Rombo Productions]]. |
| − | + | == Technical == | |
| + | |||
| + | The rom board has 8 rom slots which can be individually enabled using the dipswitches. | ||
| + | A link allows the roms to use the ids of 0-7 or 8-15. | ||
| + | |||
| + | 0-7 is compatible with the firmware in the 464 which is limited to 8 roms. | ||
| + | 0-7 or 8-15 is compatible with the firmware in the 6128 and Plus. | ||
| + | |||
| + | NOTE: Some 6128's may not support ROM 7 being overridden so if you use the range 0-7 then you should disable slot 7. | ||
| + | |||
| + | Testing was done by user nrgroom on his Rombo Rom board. | ||
| + | |||
| + | The I/O port used to select the rom (dfxx) is decoded partially and only checks A13=0 like other rom boards. | ||
| + | |||
| + | ROM ids are 8-bit and fully decoded. If range 8-15 is selected with the link then you see a rom in slot '0' in 8 only. It is not show in any other slots. I.e. it's not repeated. | ||
== Pictures == | == Pictures == | ||
| + | |||
<gallery caption="Rombo Rombox"> | <gallery caption="Rombo Rombox"> | ||
| + | |||
Image:rombo rombox 3.jpg| | Image:rombo rombox 3.jpg| | ||
Image:rombo rombox 2.jpg|A through bus expansion to connect other devices | Image:rombo rombox 2.jpg|A through bus expansion to connect other devices | ||
Image:rombo rombox 1.jpg|Inside | Image:rombo rombox 1.jpg|Inside | ||
| − | Image:rombo rombox 4.jpg|Roms individually | + | Image:rombo rombox 4.jpg|Roms individually configurable |
| + | Image:ROMBO_RomBoard_PCB_Top.jpg|PCB Top | ||
| + | Image:ROMBO_RomBoard_PCB_Bottom.jpg|PCB Bottom | ||
| + | |||
</gallery> | </gallery> | ||
| − | [[Category:Peripherals]] | + | == Manual == |
| + | |||
| + | [[Media:ROMBO ROM-Board Manual.pdf|Rombo 8 socket ROM-Board Manual]] (pdf) | ||
| + | |||
| + | [[Category:Expansion ROM]] [[Category:Peripherals]] [[Category:manual]] | ||
Latest revision as of 17:05, 3 March 2017
A ROM expansion board from Rombo Productions.
Technical
The rom board has 8 rom slots which can be individually enabled using the dipswitches. A link allows the roms to use the ids of 0-7 or 8-15.
0-7 is compatible with the firmware in the 464 which is limited to 8 roms. 0-7 or 8-15 is compatible with the firmware in the 6128 and Plus.
NOTE: Some 6128's may not support ROM 7 being overridden so if you use the range 0-7 then you should disable slot 7.
Testing was done by user nrgroom on his Rombo Rom board.
The I/O port used to select the rom (dfxx) is decoded partially and only checks A13=0 like other rom boards.
ROM ids are 8-bit and fully decoded. If range 8-15 is selected with the link then you see a rom in slot '0' in 8 only. It is not show in any other slots. I.e. it's not repeated.
Pictures
- Rombo Rombox
A through bus expansion to connect other devices
Inside
Roms individually configurable
PCB Top
PCB Bottom
