DDI clone to MX4 board adapter is done

[Piotr]

Small adapter for connect DDI both version  or other old amstrad hardware to MX4,  who need it? Can be horizontal or vertical. I just order 20 PCB.
][url=http://www.fotosik.pl]

[TFM]

How much will it cost?

[Piotr]

Hmm, approx 3 euro plus postage cost.

[Kris]

Are they gold plated or not ?

[Munchausen]

I'd be interested in one of these!

[Piotr]

Ready

]

]

]

[Pentagon]

How can i order a vertikal please?

Regards and thank you very much
Tom

[TotO]

Nice!   

The best is to use the MotherX4 passthrough connector, because:
- the floppy ribbon cable stay flat, the connexion is not weak and the board don't hide the screen.
- one slot left for a new MX4 board for all 464/664/6128 users.

[Piotr]

Yop, but i made it becouse one standart is good, but 2 standarts is better Anyway Toto where is my rom board ?? I working on HDD and without Rom Board i waste time , run man, run

[TFM]

Well, I'm sure a donation could speed up the process        

[Piotr]

Hmm i joking,but i pay for 2 devices,  i know how long real hardware is cooking But some push give amazing results sometimes.

[TotO]

Yop, but i made it becouse one standart is good, but 2 standarts is better

Sure, it's always better.
But, because the DDI-1 is an exclusive feature for 464, it's more clever to use the passthrough.

Anyway TotO where is my rom board ?? I working on HDD and without Rom Board i waste time , run man, run

I have sent it this morning. Run behind your postman, run!!!

[Piotr]

Hehehe,

]

[CraigsBar]

Sweet. How about a similar board that has a plus style connector instead of the edge connector? I know I could use ribbon cable but it'd be nicer if the connector was rigid at a height above the desk.

[Bryce]

Sweet. How about a similar board that has a plus style connector instead of the edge connector? I know I could use ribbon cable but it'd be nicer if the connector was rigid at a height above the desk.

For what? There's no expansion that needs a Centronics socket. All the old expansions were edge or had a flat cable, so using a 50way pin header connector/cable for them is easier.

Bryce.

[Piotr]

This happend when you try connect past an future. For what i d do silent .

[CraigsBar]

For what? There's no expansion that needs a Centronics socket. All the old expansions were edge or had a flat cable, so using a 50way pin header connector/cable for them is easier.

Bryce.

Oh Really?   

[Bryce]

What the hell is that??! The extremely rare bin-bag expansion?

Bryce.

[TFM]

Sweet. How about a similar board that has a plus style connector instead of the edge connector? I know I could use ribbon cable but it'd be nicer if the connector was rigid at a height above the desk.

Well, right. That's definitely needed for the 464 Plus. 

[CraigsBar]

What the hell is that??! The extremely rare bin-bag expansion?

Bryce.

It's a Brunword Elite Rom Module. In my opinion the best wordprocessor for the CPC. 

[Bryce]

It's a Brunword Elite Rom Module. In my opinion the best wordprocessor for the CPC.

I guessed it might be, but the only Brunword I ever saw was covered in black Resin, not plastic wrapped. Is there resin under the plastic, or can the PCB be seen?

Bryce.

[CraigsBar]

It is resin wrapped. The tape is only over the eprom where I chipped the resin off to dump the image to assist with Arnold support for it.

[robcfg]

It would be very nice if Piotr's MX4 setup would fit inside a FDI-1 case with the HXC display and buttons to the front... 

[awergh]

That looks nice, I guess I want horizontal for the DDI although I worry there wont be much space between my 464 and GT64 to put everything. Certainly cheaper then the serial module I almost got the other day.

[TFM]

Go into the 3rd dimension and spend your GT some 1-2 inch feet to stay on