Changes
/* Softwar Download */
Port F8B0h - CRTC Index Port F8B1h - CRTC Data Port F9B0h - Config (W) and Capture Data (R) [[NMI]] - triggered on SYNC (on VSYNC, and maybe also on HSYNC?) == Technical specs =Config Bits === Configuration is done by writing to Port F9B0h: 0 Reset Brightness/Contrast to zero (0=No, 1=Reset) 1 Increment Contrast (0=No, 1=Add +1) 2 Increment Brightness (0=No, 1=Add +1) 3 Enable NMI on Sync (0=No, 1=Yes) 4-6 Transfer mode 0=Stop Transfer 1=Transfer SRAM to CPC 3=Capture 320x200x4 to SRAM 7=Capture 640x200x1 to SRAM 7 Not used by VIDI software (set to 0) Note: additionally to above I/O controlled brightness/contrast, the hardware additionally has (externally accessible)brightness/contrast potentiometers for coarse adjustments, also the pots are REQUIRED for mode0 scans (where the brightness I/O ports are increasing from 0=min to 15=max during the 16-pass scan). === CRTC Registers === The digitizer contains a CRTC chip (the same [[CRTC]] chip that is also used in the CPC itself). The CRTC chip in the Vidi is used as address generator for writing to & reading from capture 16K SRAM. The CRTC registers are configured via Port F8B0h (index) and F8B1h (data). Usually set to following values: crtc[00h] 75h or 50h ;horizontal total (-1) crtc[01h] 50h ;horizontal displayed crtc[02h] 5Bh or .. ;horizontal sync pos crtc[03h] 11h ;horizontal sync width crtc[04h] 26h ;vertical total (-1) crtc[05h] 0 ;vertical total adjust crtc[06h] 19h ;vertical displayed crtc[07h] 0 ;vertical sync pos crtc[08h] 0 ;interlace mode crtc[09h] 07h ;max scanline (-1) crtc[0Ah] 0 ;cursor start crtc[0Bh] 0 ;cursor end crtc[0Ch] 0 ;start addr high crtc[0Dh] 0 ;start addr low crtc[0Eh] 0 ;cursor high crtc[0Fh] 0 ;cursor low crtc[10h] N/A ;lightpen high crtc[11h] N/A ;lightpen low Most registers are set to fixed values. The vidi software modifies only two of them: * CRTC[00h]. For AUX-to-SRAM it's set to 75h (vertical total=76h) (with capture writes being "paused" during hblank), for SRAM-to-CPU transfer it's set to 50h (vertical total=51h) (additional hblank cycles would be unneccesary overload for the software transfer; still there is one dummy-hblank cycle, probably required for the inner workings of the CRTC chip). * CRTC[02h]. Set to 4Bh+xpos, used to adjust the horizontal position where scanning starts. Note: The vertical position can be also changed, but this is done by software delay between vsync and capture, not by CRTC registers. In theory, more CRTC registers could be changed, for example, one could change the scanning region from 320x200 to 256x256. The Vidi software doesn't include any such features. Note: Internally, the CRTC stores the scanline data in SRAM in the same "interleaved" format as it is also used in the CPC's VRAM (ie. line 0,8,16,24,etc.). However, this effect is "undone" when the CRTC reads the stored scanlines (so the CPU receives data without interleave. oe. line 0,1,3,4,etc.). === Scanning Modes === The software supports 3 modes (at hardware side, there are only 2 modes):* Mode 2 - 640x200x1 - true hardware mode (0=black, 1=white)* Mode 1 - 320x200x4 - true hardware mode (0=black, 1=dark grey, 2=white, 3=light grey)* Mode 0 - 160x192x16 - special software mode: the software performs sixteen Mode 2 scans (with different brightness settings in each pass), and combines them to a 16-color image. Obviously, this method works only with still images (camcorder aimed at still image, or VCR with "freeze picture" mode). Moreover, the CPC with [[CTM640/CTM644]] colour monitor can't display 16 grayscales so the picture will look like crap, however, it will look pretty much perfect on a [[GT64/GT65]] green monitor. The software scans only 192 lines in this mode (not 200 lines), but this is just due to lazy programming (the programmer didn't handle the region "under" the OSD menu at the bottom of the screen). In mode 0 scanning, the user/software selected brightness is ignored (because the whole sixteen I/O selectable brightness values are used for the sixteen passes), so, brightness can be adjusted only via the potentiometer. For the two hardware modes, the bits in the capture bytes are having the same format as CPC VRAM (observe that in Mode 1, white is color 2, not color 3). For the software mode, obviously, the format depends on the software (the VIDI software uses CPC VRAM format, with color 0..15 = black..white). === Disassembly === * [[Media:Vidi digitizer disassembly.txt]] - disassembled scanning functions from VIDI software
== Pictures ==
<gallery caption="Examples of digitizing with the VIDI interface">Image:vidi.JPG|The VIDI video digitizerImage:RIMG0073.JPG|Intern VIDIImage:Vidi - Disc.jpg|Vidi Disc
Image:vidi example 1.gif|Example of VIDI digitizing
Image:vidi example 2.gif|Example of VIDI digitizing
Image:vidi example 3.gif|Example of VIDI digitizing
Image:RIMG0073Rombo Vidi Mode0 Sample on GT65.JPGpng|Mode 0 on GT65Image:Rombo Vidi Mode0 Sample on CTM644.png|Mode 0 on CTM644Image:Rombo ebay.jpg|Intern VIDIvideo digitizer as seen on Ebay 2010
</gallery>
== Manual Publicity ==
<gallery caption="VIDI ManualVidi"> Image:vidi cover.jpg|CoverImage:vidi pag 00.jpg|Page 00Image:vidi pag 01.jpg|Page 01Image:vidi pag 02.jpg|Page 02Image:vidi pag 03.jpg|Page 03Image:vidi pag 04.jpg|Page 04Image:vidi pag 05.jpg|Page 05Image:vidi pag 06.jpg|Page 06Image:vidi pag 07.jpg|Page 07Image:vidi pag 08.jpg|Page 08Image:vidi pag 09.jpg|Page 09Image:vidi pag 10.jpg|Page 10Image:vidi pag 11.jpg|Page 11Image:vidi pag 12.jpg|Page 12Image:vidi pag 13.jpg|Page 13
Image:Vidi Publicity 1.jpg|Advert 1
Image:Vidi Publicity 2.jpg|Advert 2
Image:VIDI ad ACU March1987.jpg|Advert 3
</gallery>
== Reviews == * [[ACU Issue 12, 1986]], page [[:Image:Amstrad Computer User8612049.jpg|49]], [[:Image:Amstrad Computer User8612050.jpg|50]]* [[Amstradbladet 1987, Issue 4]] page 8-11 (Danish)* [[Amstrad Action, Issue 115, 1995]] page 19 == Manual in PDF == * [[Media:Vidi Manual.pdf|VIDI Manual]] (pdf)* [[Media:Vidi Manual.txt|VIDI Manual]] (txt) == Software Download == * [[Media:Rombo Video Digitiser.zip|Rombo Video Digitiser.zip]] (DSK for Emulators)* [[Media:VIDIR202.ROM|Rombo Video Digitiser ROM]] (ROM for ROM expansions)
* [[ARA Video Digitizer]] - another video digitizer ([[Jagot & Leon]])
[[Category:HardwareGraphic]] [[Category:Peripherals]] [[Category:Manual]] [[Category:Stub]]
